1979-1995 Toyota Rear Long Travel Leaf Springs (Pair)
79-95 Toyota Rear Long Travel Leaf Springs (Pair)
All-Pro's Rear Long Travel Leaf Springs are 9″ longer than factory (’79-’88) rear springs. Mounting these longer springs will require new front spring hangers and relocation of the rear shackle hangers on pre-’89 trucks. Our rear springs have 8 leaves, plus a special torque leaf to reduce axle wrap. Springs come with new poly bushings. See below for spring specifications. We do not have stock length rear springs available.
When installing the same lift onto a 4Runner, the rear springs will need to be 1″-2″ taller than the front to compensate for the added weight of the vehicle. 1984-1989 4Runners weigh an average of 700lbs more than the pickup because of the hardtop, glass, interior components, roll bar, heavier tailgate and power window assembly inside, and other components. If you always run your 4Runner empty in back, a 1″ taller rear spring will generally be enough to level it with the front. If you carry spare parts or extra passengers in back we recommend a 2″ taller spring than the front.
Sold in pairs.
NOTE: These springs are NOT designed for weight carrying capability. They are designed for ride quality and flex. If you intend to use the vehicle for carrying weight, we recommend adjusting the bump stops to prevent bottoming out and damaging the shocks or springs and adding airbags or other support devices.
4″ Leaf Spring Specifications:
- Number of Leaves: 8 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 51-7/8″ (1318 mm)
- Front Eyelet to Center Pin (Free): 24-7/8” (632 mm)
- Rear Eyelet to Center Pin (Free): 27” (686 mm)
- Spring Rate: 207 lbs/in
5″ Leaf Spring Specifications:
- Number of Leaves: 8 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 51-78″ (1318 mm)
- Front Eyelet to Center Pin (Free): 24-9/16” (624 mm)
- Rear Eyelet to Center Pin (Free): 27-5/16” (694 mm)
- Spring Rate: 204 lbs/in
6″ Leaf Spring Specifications:
- Number of Leaves: 8 + 1 Overload/Rebound
- Eyelet-to-Eyelet Length (Free): 51-1/2″ (1308 mm)
- Front Eyelet to Center Pin (Free): 24-7/16” (621 mm)
- Rear Eyelet to Center Pin (Free): 27-1/16” (687 mm)
- Spring Rate: 196 lbs/in
Please note:
- Using a lifting block or shackle flip with our springs will void the All-Pro warranty
- Leaf springs are shipped without packaging. It is normal for springs to be scratched by freight carriers during the shipping and handling process and by customers during installation. We recommend that leaf springs be touched up with spray paint after they are installed to cover any bare metal exposed during shipping and installation.
WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov
- 8 leaves.
- Special torque leaf to reduce axle wrap.
- Springs come with new poly bushings.
- Sold in Pairs
TOYOTA 4RUNNER
(1986-1995)
1986 Toyota 4Runner
1987 Toyota 4Runner
1988 Toyota 4Runner
1989 Toyota 4Runner
1990 Toyota 4Runner
1991 Toyota 4Runner
1992 Toyota 4Runner
1993 Toyota 4Runner
1994 Toyota 4Runner
1995 Toyota 4Runner
TOYOTA PICKUP
(1979-1995)
1979 Toyota Pickup
1980 Toyota Pickup
1981 Toyota Pickup
1982 Toyota Pickup
1983 Toyota Pickup
1984 Toyota Pickup
1985 Toyota Pickup
1986 Toyota Pickup
1987 Toyota Pickup
1988 Toyota Pickup
1989 Toyota Pickup
1990 Toyota Pickup
1991 Toyota Pickup
1992 Toyota Pickup
1993 Toyota Pickup
1994 Toyota Pickup
1995 Toyota Pickup
1. Install bushings into the springs using polyurethane-safe grease. If applicable, install the sleeves into the bushings.
2. Mount the springs to the vehicle. The end with the military wrap should be at the front.
3. Check to make sure the long side of the bolts on the spring clamps are pointed towards the inside of the vehicle.
4. Fully cycle the suspension and verify that no part of the springs interfere with other suspension components (e.g. shocks). Also verify that the brake lines are long enough and do not stretch at maximum droop or get pinched by other components. In some instances, leaf spring clamps may need to be removed or relocated to avoid interference with other components.
5. If you have any questions or concerns, please e-mail your questions to tech@trail-gear.com
or call us at 559.549.6737.
ALL-PRO products are warranted to be free from defects in materials and workmanship prior to installation. Any alteration, improper use, or modification will void this warranty. This warranty is extended by All-Pro to the original purchaser. This warranty is effective for 90 days from the date of purchase. Any description of the goods is for the sole purpose of identifying them, is not a part of the bargain, and does not constitute a warranty that the goods will conform to that description. Any sample, model or advertised item is for illustrative purposes only, is not part of the basis for the bargain, and is not to be construed as a warranty that the good will conform to the sample, model, or advertised item. No affirmation of fact or promise made by All-Pro will constitute a warranty that the goods will conform to the affirmation or promise.
Purchasers and users of our products are responsible for determining the applicability of a product to their specific application. In the event of a defect, malfunction, or failure to conform to this warranty, All-Pro will repair or replace the goods without charge within 30 days of receipt of goods. If All-Pro is unable to replace and/or repair the goods or if All-Pro, at its sole discretion, determines that neither option is commercially practicable or cannot be made within 30 days of receipt of the goods, All-Pro will refund the purchase price. The purchaser is responsible for installation and removal of all parts, freight or shipping costs, and incidental or consequential damages.